When using a laser engraving machine, here are the 12 most important things to remember

Maintaining a laser engraving machine is similar to maintaining a laser marking machine.

Laser engraving machines and laser power supplies require grounding, and the grounding wire should be less than four special grounding wires. laserpecker metal engraving The grounding wire should be the following:

Provides a normal laser power supply,

Increase the laser tube's service life,

In addition, it prevents the machine from being beaten by external interference,

Accidental circuit damage should be prevented by preventing high voltage discharges.

Consistent flow of the cooling water is essential for optimal performance of the laser engraving machine. Whether utilizing tap water or circulating pumps, it is imperative to maintain a steady flow as this water plays a vital role in dissipating the heat produced by the laser tube. The temperature of the water should be maintained between 15-20 ° C to prevent a decline in optical output power. Immediate repairs must be carried out if there is a disruption in the cooling water supply to avoid possible equipment damage or reduced power output. Regular inspections should also be conducted to ensure uninterrupted flow of the cooling water.

As with stiff joints affecting human movement, the guide rail is a crucial part of maintaining a machine tool that requires regular cleaning and proper maintenance. For optimal performance, it should be cleaned after every research task and lubricated afterward. The bearings should also be oiled regularly in order to maintain flexibility in the driving mode, achieve precise processing technology, and prolong the machine tool's lifespan.

The temperature and humidity should be between 5 and 35 degrees Celsius, and the following should be considered:

To prevent freezing, drain the circulating water after shutting down the laser tube;

For the laser to function normally, it must be preheated for at least five minutes before use. To prevent the high voltage circuit from failing and improve the high voltage on rainy days and humid environments, it should be preheated for a long time until it is properly dehumidified.

Proper use of the Laser High Voltage button is of utmost importance. Activating this button will place the laser power supply in standby mode. To prevent any accidental harm to people or objects, it is essential to deactivate the "laser high voltage" (also called laser current) after each task. Additionally, operators must not leave without consent while the machine is operational. For optimal safety, it is advisable to restrict continuous work to 5 hours with a 30-minute break between sessions.

In order to prevent potential damage to the national machinery market, large welding machines, enterprise power mixers, and equipment for power transmission and transformation should be kept at a safe distance. In addition, forging presses and nearby motor vehicles should be avoided since they can disrupt precise engraving. These situations are rare, but they should still be avoided when possible.

In addition, "good grounding" can also help prevent lightning as long as the building's lightning protection measures are reliable. To prevent sudden electrical failures in unstable areas (such as those with voltage fluctuations greater than 5%), install a regulated power supply of at least 3000W.

You should only use your control PC if you have graphic design software available on it. Make sure it is stable if you are using it to operate engraving equipment. A network card and an antivirus firewall on this computer can significantly slow down the controller. If data communication is necessary, disable the network card before starting the engraving machine.

With a cotton cloth, wipe off the original oil and dust on the guide rail and then apply a layer of oil to the surface and sides of the rail. Maintenance period: A week.

It is normal for dust to accumulate in the fan and exhaust pipe of the fan over time, which affects the fan's efficiency and causes a lot of smoke to be released. The exhaust duct must be removed from the fan, the dust cleaned from the exhaust duct must be removed, and the hose connecting the fan to the exhaust duct must be loosening for approximately one month.

The motion control system will produce some loose, loose screws during the development phase, which will affect the stability of the movement as we develop the mechanical design. One month is the maintenance life cycle for tightening the screws individually with the included tools.

Maintaining the lens is vital for the smooth operation of a laser engraving machine. Over time, exposure to external elements can cause the accumulation of ash, resulting in decreased reflectivity and transmittance. This can have a negative impact on the overall performance of the machine. To prevent this, use alcohol-dampened cotton to gently wipe the lens surface in a clockwise direction and eliminate any dust. Regularly performing this upkeep is essential for extending the lifespan of the machine and maximizing its efficiency.